For an easy introduction to single coil DIY building, this GeekVape AMMIT 25 RTA is hard to beat. As well as creating more build space, this 25mm diameter version of the AMMIT RTA also operates at higher power settings. Though the kit comes fitted with a TPD compatible, 2ml capacity glass section, GeekVape also include a longer chimney and a 5ml capacity tank extension.
With the AMMIT 25mm rebuildable tank atomizer (RTA), GeekVape set-out to create a tank that would be easy for inexperienced self-builders to handle. The AMMIT tank is designed to work with a single coil wire (not supplied). You can either wind your own coil, or buy pre-wound coils from most vape stores.
By designing one of the two build-deck posts with an ‘open’ terminal connector, GeekVape have made it easier than ever to fit the coil. The coil wires are clamped in position with two flat-headed grub screws. The kit comes with a special 3-way screwdriver. The only tricky part of setting up an AMMIT 25 RTA is trimming the coil wires. Most experienced builders recommend that you bend the ends of the wires until they snap off at the grub-screw.
After fitting and wicking a coil (organic cotton not supplied) you’ll need to soak the wick with e juice, then reassemble the AMMIT RTA for filling. Before you fill the tank, remember to close the juice flow control ports – this will prevent any leaks. After that, simply unscrew the top-cap and drip your e juice down into one of the dual, kidney shaped fill ports. Replace the top cap, open up the e juice flow control ring and you’re ready for vaping. The RTA comes with two separate top-caps; the fitted cap has a 510 Delrin drip-tip, the alternative cap is compatible with 810 drip-tips (not supplied).
The adjustable airflow ring on the base of the RDA provides ‘3D’ airflow to your fitted coil. As well as producing spectacular cloud density, the AMMIT 25 tank delivers phenomenal flavour. Simply adjust the airflow ring to fine tune the vape for warmth and flavour at your chosen wattage.
This single coil, AMMIT 25mm rebuildable atomizer comes with a Stainless Steel finish.
E liquid isn’t supplied with this GeekVape RTA. Please visit our E liquids pages, or click here to add one of our flavoursome e juices to your order.
1 x GeekVape AMMIT 25mm RTA (2ml Capacity)
1 x 510 Delrin Drip-Tip & Top-Cap (Fitted)
1 x 810 Compatible Top-Cap (Alternative)
1 x 5ml Alternative Tank Glass
1 x Stainless Steel Chimney Extension
1 x 3-Way Screwdriver & Spare Parts
1 x Instruction Manual
GeekVape AMMIT 25 RTA Features:
Base diameter: 25mm
Height: Around 48mm (with drip-tip)
TPD tank capacity: 2ml
Standard 510 mod connection
Comes with a fixed positive pin
Comes with alternative 5ml glass & chimney extension
Features reinforced, heat-proof tank glass
Type: Single coil, dual post rebuildable tank atomizer (RTA)
Comes with 510 wide-bore Delrin drip-tip & top cap
Alternative 518 top-cap included (without drip-tip)
Suitable for single coil DIY building
Unscrew top-cap for filling
Dual kidney shaped e juice fill ports
Has an e juice flow control ring for leak-free filling
Airflow adjuster ring on base
2 x Cyclops airflow slots
3D side & below airflow to coil
Dual post deck
Coils not included
One post has a ‘slot’ for easier coil attachment
2 x Flat-head grub screws for terminal retention
3-Way screwdriver included
Wicking holes designed for easy placement
Wicking cotton not supplied
Spare O rings & screws provided
Deck designed for simple, single-coil building
Well designed & manufactured
Top-class flavour performance
Produces rich, dense cloud
Comes with a Stainless Steel finish
AMMIT 25 RTA Compatibility:
The AMMIT 25 RTA has a base diameter of 25mm. This rebuildable tank atomizer is designed for easier DIY coil building. As well as reading the supplied GeekVape manual, buyers must be familiar with Ohm’s law, vaping battery safety, coil resistance and wire types.
Check out our warranty terms & conditions page here.
Posted by RR on 17th Oct 2018
I decided to try DIY coil building but drippers looked frustrating, having to repeatedly drip into the thing! I don't have the patience for that!
So an rdta looked like it would be ideal for me.
I decided on the Geekvape Ammit becos I already have a couple of their mods and I know the quality, as I prefer something that I know will last.
I brought a blue one which suits the mod it's on nicely (Dovpo Rogue 100).
It's REALLY easy to set-up - honest, if I can do it then anyone can!!
The fiddliest bit is getting the coil in, but it's not too tricky - and only one so even better.
Getting the cotton right I found to be an interesting experience! But I am getting it right now.
The rest goes together nicely.
The drip tip isn't wide bore, which I prefer, and works well. The airflow holes are fully adjustable and I close them up whilst the juice ports are open - ta-da!! No leaks!!!
Clouds are pretty good but as I vape for flavour this vape gives me loads!! Lush!
Loads useful bits in the box - cotton too!
If you're nervous in trying out coil building DON'T BE with this rdta, honestly I am SOOOO pleased I took the plunge. It's WAY cheaper than buying coils too.
Only thing abit disappointing is the Ammit colour range isn't massive, however the quality shines through.